Women’s Waterproof Hiking Shoes - MH100 Mid Blue/Purple

8595692

QUECHUA

From

₹ 3,999.00

Women’s Waterproof Hiking Shoes - MH100 Mid Blue/Purple

Made for
Provide comfort and protection for your feet, thanks to cushioning along the entire length of the sole, support for the high-top upper and a waterproof membrane to keep them dry.
Sizes guide

Advantage
TractionNon-slip rubber outsole with 4mm gripping studs.
Impact protectionStone-guard in strong rubber on the front of the foot to protect the toes.
WaterproofWaterproof and breathable membrane lining: your feet dry for 3h in all weather
CushioningFull-length cushioning thanks to an EVA midsole
FitHigh-top upper. Locking hooks to spread lacing between the foot and ankle
Lightweight395 g per boot in size 6
Warranty2 Years
Technical Information

1
WHAT IS YOUR HIKING FREQUENCY AND INTENSITY?
We have classified our products in terms of performance and features for 3 levels of Mountain Walking: - occasional: about 10 hikes per year of about 3 to 4 hours in length, covering less than 10km and less than 700m in elevation gain. - Regular: about 20 outings per year. 4 to 6 hours, 10 to 20 km, 700 to 1200m of elevation gain per outing. - Intensive: more than 20 times a year. More than 6 hours, more than 20 km, 1200 to 2000m of elevation gain per outing.
2
SUSTAINABLE DEVELOPMENT INFORMATION
For the fabric covering the insole of these shoes, we dye the yarn at source in order to reduce the environmental impact. Textile dyeing requires a lot of water but also produces waste water from the dye baths. To reduce this environmental impact, we use a bulk dyeing process that involves adding the colour pigments when the yarn itself is produced.
3
SOLE WITH GRIP
The grip of our soles is certified. To be awarded certification, the boots must pass laboratory tests to assess the grip rate on different surfaces (Smooth, Rugged, Dry, Wet). To validate these tests, we assess the quality of our soles in the field, in the mountains, by a panel of representative testers over 500 km
4
Waterproofing test
In the laboratory, the shoe is placed in water up to the middle of the upper on a mechanical arm that flexes the shoe to simulate a number of steps. With this test we can determine a time and number of km that the boot can walk while staying dry. Then we validate this in the field and in the rain to make sure that the shoe keeps its promises in use.
5
Making waterproofing last longer
To keep your feet dry, we advise you to use a waterproof gaiter or mini-gaiter to protect the top of your boots and prevent water, pebbles and sand from getting in. We advise re-waterproofing your boots twice a year using a re-waterproofing agent (search for ‘waterproofing’ on our Decathlon website) which will help you restore the original water-repellent qualities and help prevent stains on the outside.
6
Which size should I select?
The most important thing is to try on several sizes and styles of boots to find the one most suited to you! You can take a size above your usual one to prevent the toes from bumping into the toe box when going downhill, provided the foot is properly supported to avoid friction. Tip: keep your toenails short and, before a long descent, check that your lacing is tight enough to prevent your foot from sliding forwards inside the boot.
7
HOW DO YOU AVOID BLISTERS?
8
BUYING TIPS / HOW DO YOU TRY YOUR BOOTS ON?
Some Decathlon stores have a test route. 1. Try on both shoes, standing up, with the socks worn for hiking. 2. Tighten the laces, taking care to correctly balance the tightening. 3. Check two points: - the heel does not come up before the boot when you walk uphill. - the foot does not slide and the toes do not press against the front when going downhill. 4. Try on several sizes and models. Break them in gradually to adapt them to your foot.
9
Which socks?
A waterproof boot will be less breathable than a non-waterproof boot. Socks like the MH500, MH520 and MH900 with a high or medium upper (adapted to the height of the boot) are therefore preferable for wicking away perspiration and reducing friction.
10
Optimise the capabilities of your boots: replace your insoles!
The original insole in your boots is designed to accommodate most feet. A change of insole can bring: 1. Improved support: some soles are preformed or reinforced to better support the arch of the foot. 2. More comfort: the insoles can also provide heat and/or cushioning. 3. Longer life: restore the support and comfort of your shoes by replacing the insole each season.
11
Lab tests
Further laboratory tests were conducted to test the following elements: attachment of eyelets and webbing, assembly, toxicology, UV resistance, sole and upper component abrasion, accelerated ageing.
12
How should you look after your boots?
- Leave to air-dry. - Remove dry mud with a stiff brush. - For stains, clean with a brush and a little warm water - Leave to dry - Spray with a re-waterproofing agent to restore the water-repellent properties of the upper.
Information / Concept / Technology
Composition
Outer sole of : 70.0% Rubber - Styrene Butadiene Rubber, Outer sole of : 30.0% Ethylene Vinyl Acetate Upper of : 68.1% Polyester, Upper of : 17.5% Polyurethane, Upper of : 14.4% Leather - Bovine - Split Lining and sock of : 90.0% Polyester, Lining and sock of : 10.0% Polyamide

Product test
All our boots are tested for initial comfort and comfort in use by hikers from outside Decathlon under the same conditions you find in use. The aim is to test, develop and confirm the product in the most objective way possible, so you can get maximum enjoyment out of hiking!

Stockage tips
Store in a well ventilated dark, dry place.
Show results for